Tesamorelin Dosing Calculator & Reconstitution Guide
A growth hormone releasing hormone analog researched for visceral fat reduction.
Tesamorelin is a research peptide. A growth hormone releasing hormone analog researched for visceral fat reduction. To dose it, reconstitute the vial (for example 5 mg in 2 mL of bacteriostatic water for 2.5 mg/mL), then divide your target dose by that concentration to find the units to draw.
- Category
- research peptide
- Dose unit
- mg
- Commonly reported range
- 1-2 mg
- Typical concentration
- 2.5 mg/mL
Use the Keel dose calculator to enter your numbers and see the exact units to draw, or use the built-in calculator further down this page.
What is Tesamorelin?
Tesamorelin is a stabilized growth hormone releasing hormone analog studied for reducing visceral adipose tissue. Anecdotal community and research reports commonly cite daily doses in the 1-2 mg range. Also known as Egrifta.
How many units is each Tesamorelin dose?
| Dose | Volume to draw | Units (U-100) |
|---|---|---|
| 1 mg | 0.4 mL | 40 units |
| 2 mg | 0.8 mL | 80 units |
Based on a 5 mg vial reconstituted with 2 mL of bacteriostatic water (2.5 mg/mL) and a U-100 insulin syringe. The dose amounts shown are commonly reported by the community and in anecdotal research, not recommendations or medical advice; only the reconstitution math (volume and units) is calculated for you.
How to calculate a Tesamorelin dose
- 1
Choose your vial and water
Select your Tesamorelin vial size (for example 5 mg) and the volume of bacteriostatic water you will add (for example 2 mL).
- 2
Find the concentration
Divide vial milligrams by water volume. 5 mg in 2 mL gives 2.5 mg/mL.
- 3
Calculate the draw
Divide your target dose by the concentration to get the volume in mL, then multiply by 100 to get units on a U-100 insulin syringe.
- 4
Verify on the syringe
Use the Keel calculator to see the exact draw rendered on a to-scale syringe, with a warning if the dose exceeds the syringe capacity.
Tesamorelin dosing FAQ
How do I reconstitute Tesamorelin?
A common approach is to add 2 mL of bacteriostatic water to a 5 mg vial, which gives 2.5 mg/mL. Add the water slowly down the vial wall, swirl gently rather than shaking, and let the powder dissolve fully before drawing.
How many units is 2 mg of Tesamorelin?
At 2.5 mg/mL, 2 mg equals 0.8 mL, which is 80 units on a U-100 insulin syringe.
What Tesamorelin doses do people report?
Community and anecdotal reports commonly cite 1 to 2 mg. These are figures people report, not a recommendation from Keel. Tesamorelin is a stabilized growth hormone releasing hormone analog studied for reducing visceral adipose tissue. Anecdotal community and research reports commonly cite daily doses in the 1-2 mg range.
Which insulin syringe should I use for Tesamorelin?
A U-100 insulin syringe is standard. A 0.3 mL (30-unit) syringe gives the most precise measurement for small draws, while a 0.5 mL or 1 mL syringe is better when the draw exceeds 30 units. Keel warns you when a dose is larger than the syringe you select.
How should I store Tesamorelin after reconstitution?
Reconstituted peptides are generally kept refrigerated and protected from light, with the unmixed powder stored cooler still. Follow the guidance from your supplier or a licensed healthcare professional for the specific compound.
What if my Tesamorelin dose is larger than the syringe holds?
Either use a larger insulin syringe or reconstitute with more bacteriostatic water to lower the concentration, which increases the volume per dose so it fits. Keel flags an over-draw and you can adjust the inputs until the draw fits.
Is Tesamorelin dosing the same for everyone?
No. The right draw depends on your vial size, how much bacteriostatic water you add, and your target dose. Always recalculate when any of those change, and consult a licensed healthcare professional.
Tesamorelin side effects
See the adverse effects most commonly reported for Tesamorelin and its class, and log your own experience over time, in the Peptide & GLP-1 Side Effects reference & tracker.